NewStats: 3,259,519 , 8,170,404 topics. Date: Sunday, 25 May 2025 at 12:31 PM n312f

My honda accord 2013 - when i am in traffic and i put on the ac when the gear is engaged, it vibrates serioiusly and the oil light blinks on the dashboard and when i try to accelerate the car wont move until i turn off the AC

Please is the shock absorber (driver side only) of Honda civic 2007 up to 16k?

Mafuba:
My honda accord 2013 - when i am in traffic and i put on the ac when the gear is engaged, it vibrates serioiusly and the oil light blinks on the dashboard and when i try to accelerate the car wont move until i turn off the AC

Your compressor could be freezing up.
What's your repair history? Did you change AC compressor recently?

Hi, here are the symptoms evident in my EOD 2005 Asian model:
- High fuel consumption
- Pushing the turtle all the way to the ground sometimes and would still not move and other times, it will move with a soft touch (as at today, this one appears solved)
- Black soothe from the exhaust.
- RPM raising itself beyond 1 after setting it between 0.7 and 0.9. This happens after going for a little drive

I've changed the airflow metre as well as the injector mouth but these symptoms persists. Scanner reveals no error. Please what is the issue here??

PS: It was purchased brand new by the previous owner. Also, the car does not come with any O2 sensor surprisingly

SegunWamiri:
Hi, here are the symptoms evident in my EOD 2005 Asian model:
- High fuel consumption
- Pushing the turtle all the way to the ground sometimes and would still not move and other times, it will move with a soft touch (as at today, this one appears solved)
- Black soothe from the exhaust.
- RPM raising itself beyond 1 after setting it between 0.7 and 0.9. This happens after going for a little drive

I've changed the airflow metre as well as the injector mouth but these symptoms persists. Scanner reveals no error. Please what is the issue here??

PS: It was purchased brand new by the previous owner. Also, the car does not come with any O2 sensor surprisingly

Waiting for error codes is like a woman waiting to give birth after 9months

Who knows a good place to do wheel alignment and Balancing in Yaba?

Wizdeen:
Who knows a good place to do wheel alignment and Balancing in Yaba?

Go to MRS petrol station. They do a good job there.

mayor2013:


Waiting for error codes is like a woman waiting to give birth after 9months

Why do you say his vehicle won’t throw any error codes?

[quote author=luvinhubby post=123658587]

I need a complete vtc solenoid assembly and rocker arm sensor for 04 Honda accord.

The error code after scanning my car repeatedly is P2646.

I have changed the switch vtc sensor switch without effect and also replaced the rocker arm sensor but the check engine light still there.

What prompted the scanning was that I noticed vibration/jacking once the RPM reach 3000 and a rewire worked on it we changed this stuffs and jacking stopped but the check engine light was still there.

And still pointing to the rocker arm, what the rewire did I didn't know. But sometimes when it gets to that 3000rpm there's soft jacking lately but not up to the previous ones. What's the cost for the above mentioned parts new/tokunbo whichever you can guarantee.

One more thing, I noticed the RPM is always high when I start the car in the morning and it takes like over 10 mins to come back to like 1100rpm which I'm not satisfied with, I had someone checked that out, we cleaned the throttle head with cab cleaner and it seem normal for a while but it continued again and it's consuming fuel lately. I don't want issue that will be consuming fuel atleast not this time abeg lol.

I am of the opinion if I can replace the two stuffs I mentioned up there completely, I hope it'll help solve the RPM and all.

I need the total cost and I can get it way billed to me or come down to fix it. I live in Sango Otta axis.

luvinhubby:

Budget 30k for toks & 28k for new

I need a complete vtc solenoid assembly and rocker arm sensor for 04 Honda accord.

The error code after scanning my car repeatedly is P2646.

I have changed the switch vtc sensor switch without effect and also replaced the rocker arm sensor but the check engine light still there.

What prompted the scanning was that I noticed vibration/jacking once the RPM reach 3000 and a rewire worked on it we changed this stuffs and jacking stopped but the check engine light was still there.

And still pointing to the rocker arm, what the rewire did I didn't know. But sometimes when it gets to that 3000rpm there's soft jacking lately but not up to the previous ones. What's the cost for the above mentioned parts new/tokunbo whichever you can guarantee.

One more thing, I noticed the RPM is always high when I start the car in the morning and it takes like over 10 mins to come back to like 1100rpm which I'm not satisfied with, I had someone checked that out, we cleaned the throttle head with cab cleaner and it seem normal for a while but it continued again and it's consuming fuel lately. I don't want issue that will be consuming fuel atleast not this time abeg lol.

I am of the opinion if I can replace the two stuffs I mentioned up there completely, I hope it'll help solve the RPM and all.

I need the total cost and I can get it way billed to me or come down to fix it. I live in Sango Otta axis.

berbs112:




I need a complete vtc solenoid assembly and rocker arm sensor for 04 Honda accord.

The error code after scanning my car repeatedly is P2646.

I have changed the switch vtc sensor switch without effect and also replaced the rocker arm sensor but the check engine light still there.

What prompted the scanning was that I noticed vibration/jacking once the RPM reach 3000 and a rewire worked on it we changed this stuffs and jacking stopped but the check engine light was still there.

And still pointing to the rocker arm, what the rewire did I didn't know. But sometimes when it gets to that 3000rpm there's soft jacking lately but not up to the previous ones. What's the cost for the above mentioned parts new/tokunbo whichever you can guarantee.

One more thing, I noticed the RPM is always high when I start the car in the morning and it takes like over 10 mins to come back to like 1100rpm which I'm not satisfied with, I had someone checked that out, we cleaned the throttle head with cab cleaner and it seem normal for a while but it continued again and it's consuming fuel lately. I don't want issue that will be consuming fuel atleast not this time abeg lol.

I am of the opinion if I can replace the two stuffs I mentioned up there completely, I hope it'll help solve the RPM and all.

I need the total cost and I can get it way billed to me or come down to fix it. I live in Sango Otta axis.

Are you sure the sensors are the issue? Dig further and also resolve other likely cause of the issue

Dozieson:


Are you sure the sensors are the issue? Dig further and also resolve other likely cause of the issue

The error code is p2646 and that's all it brings at all time. The only error code

berbs112:


The error code is p2646 and that's all it brings at all time. The only error code

https://nairaland.unblockandhide.com/6420434/honda-2004-5-how-fix

Study the link properly

I am suspecting wrong oil weight or low oil

Another link below throws more light

https://www.700r4transmissionhq.com/p2646-honda-accord/

https://nairaland.unblockandhide.com/6420434/honda-2004-5-how-fix

Study the link properly

I am suspecting wrong oil weight or low oil

Another link below throws more light

https://www.700r4transmissionhq.com/p2646-honda-accord/

Will do. Thank you Boss

Hello house. I scanned my 2008 Honda Accord and this is the code that came up;

P0011

I cleared the code and drove again, and the code came back. Research online shows that I should have symptoms like rough idle and reduced acceleration, but I don't. Car idles well and accelerates fine.

I want to tell a mech to remove the vtc filter and clean, but I'm not sure and I don't want any unnecessary poking into my engine.

Pls any competent Honda mech in Ibadan?

theadeola:
Hello house. I scanned my 2008 Honda Accord and this is the code that came up;

P0011

I cleared the code and drove again, and the code came back. Research online shows that I should have symptoms like rough idle and reduced acceleration, but I don't. Car idles well and accelerates fine.

I want to tell a mech to remove the vtc filter and clean, but I'm not sure and I don't want any unnecessary poking into my engine.

Pls any competent Honda mech in Ibadan?

Are you still going back and forth on this?
Thought you've done it already.

jceesquare:

Are you still going back and forth on this?
Thought you've done it already.

I was going to do it, but need a competent Honda mech. Not sure about the expertise of my mech with regards to Honda.

theadeola:


I was going to do it, but need a competent Honda mech. Not sure about the expertise of my mech with regards to Honda.

Then call 07089030689 if in Lagos

jceesquare:

Then call 07089030689 if in Lagos

Unfortunately, I'm not. I'm in Ibadan, and I've been looking for a good Honda mech here.

theadeola:


Unfortunately, I'm not. I'm in Ibadan, and I've been looking for a good Honda mech here.

DIY. It is a simple task. Check YouTube on how to check if the solenoid is working well. Also make sure your oil is guaged

Dozieson:


DIY. It is a simple task. Check YouTube on how to check if the solenoid is working well. Also make sure your oil is guaged

Okay, will do. I just changed the oil in the car after I got it. The former owner didn't do maintenance on time, was showing 15% oil life when I got it. So I changed oil with 10w 40 synthetic oil and oil filter.

That made the rocker arm code disappear, leaving this one. I hope I don't need any special tool for the diy thing Sha.

Thank you very much

Good evening all...!!

Pls I need solution and help on my Honda Civic 06 American spec

I bought a new engine a month ago.... I notice if I drove my Car for few mins or accelerates , they engine light we start blinking which will result to my car movement slow each times it comes up... So I took they car to my electrical, lastweek scanned it, which it show's 1, 3 and 4 cylinder error.. I was told to buy new plug which, I did and it seems to be worst, so I have to changed back to they tok plug they engine comes with... So I took they car to mechanic which he confirm that my 4 coil and plug are all Good...!! But I can't enjoy a smooth drive


Pls right now I'm really worried... !! Any suggestion or something else to looking into ... And does this issue has anything to do all with my bainbox

Pls I'm stranded and loss of thoughts they engine is barely a month old

Pls anyone with similar experience or solution should pls help

Deigofortune:
Good evening all...!!

Pls I need solution and help on my Honda Civic 06 American spec

I bought a new engine a month ago.... I notice if I drove my Car for few mins or accelerates , they engine light we start blinking which will result to my car movement slow each times it comes up... So I took they car to my electrical, lastweek scanned it, which it show's 1, 3 and 4 cylinder error.. I was told to buy new plug which, I did and it seems to be worst, so I have to changed back to they tok plug they engine comes with... So I took they car to mechanic which he confirm that my 4 coil and plug are all Good...!! But I can't enjoy a smooth drive


Pls right now I'm really worried... !! Any suggestion or something else to looking into ... And does this issue has anything to do all with my bainbox

Pls I'm stranded and loss of thoughts they engine is barely a month old

Pls anyone with similar experience or solution should pls help

Share the scan codes here. You will get better response

I'm in the market for a Civic 08-10 model?
ed pls.. car must be in reasonable good shape with primary systems in good working condition.
if you have such a vehicle for sale.
P.S. Vehicle must be located in Lagos.
Proximity to Surulere won't be bad.
: 08184052425 (WhatsApp)

HenryWilliams:
I'm in the market for a Civic 08-10 model?
ed pls.. car must be in reasonable good shape with primary systems in good working condition.
if you have such a vehicle for sale.
P.S. Vehicle must be located in Lagos.
Proximity to Surulere won't be bad.
: 08184052425 (WhatsApp)

There is one at Aguda, you can come inspect by weekend.
Nelson- +234 806 345 5474

Deigofortune:
Good evening all...!!

Pls I need solution and help on my Honda Civic 06 American spec

I bought a new engine a month ago.... I notice if I drove my Car for few mins or accelerates , they engine light we start blinking which will result to my car movement slow each times it comes up... So I took they car to my electrical, lastweek scanned it, which it show's 1, 3 and 4 cylinder error.. I was told to buy new plug which, I did and it seems to be worst, so I have to changed back to they tok plug they engine comes with... So I took they car to mechanic which he confirm that my 4 coil and plug are all Good...!! But I can't enjoy a smooth drive


Pls right now I'm really worried... !! Any suggestion or something else to looking into ... And does this issue has anything to do all with my bainbox

Pls I'm stranded and loss of thoughts they engine is barely a month old

Pls anyone with similar experience or solution should pls help

Refurbished engine or bad plug coils

Good evening all

Please I plan on getting a 2008 Accord . I notice that when the key is turned to position 2 (without staring the Engine). All dashboard lights comes on except the check Engine Light.

I believe it’s meant to show when the ignition is turned and disappear when the engine is started.

Is it a serious flag pls?

piehorse:
Good evening all

Please I plan on getting a 2008 Accord . I notice that when the key is turned to position 2 (without staring the Engine). All dashboard lights comes on except the check Engine Light.

I believe it’s meant to show when the ignition is turned and disappear when the engine is started.

Is it a serious flag pls?

Hmmmm

piehorse:
Good evening all

Please I plan on getting a 2008 Accord . I notice that when the key is turned to position 2 (without staring the Engine). All dashboard lights comes on except the check Engine Light.

I believe it’s meant to show when the ignition is turned and disappear when the engine is started.

Is it a serious flag pls?

Waiting for Angrygoat to come and advice you

2 and 3 samething. Just that position 3 means engine on and all lights suppose off. If dem nO off after engine don on then problem dey.

Kingdemu:
Waiting for Angrygoat to come and advice you

piehorse:
Good evening all

Please I plan on getting a 2008 Accord . I notice that when the key is turned to position 2 (without staring the Engine). All dashboard lights comes on except the check Engine Light.

I believe it’s meant to show when the ignition is turned and disappear when the engine is started.

Is it a serious flag pls?

Make sure the check engine light isn't blocked from the instrument cluster. People do this to hide the fact that something wrong with the car. They simply open the instrument cluster and cover the indicator

Collione:


Make sure the check engine light isn't blocked from the instrument cluster. People do this to hide the fact that something wrong with the car. They simply open the instrument cluster and cover the indicator

My thought